Axes 5/023 Move monorail columns 350mm left

This walking level should be at elev. 6,5m, not the same of the ASU
We will have a step along this line
Axes 8/023

Platform B – (022/10-11): adjust handrail according to Layout dimensions (right picture)
Axes 10/022

Move monorail from 0,00 to 4,65 (platf. A1)
Axes 5/017
Also remember to provide removable handrail (1m centered)
Looks like you used same monorail of ASU, this should be smaller, it downloads only the empty filters of the Drypan

Stairs to be minimum 1 meter for safety evacuation
(net dimension between handrails)
Axes 6/016
Axes 7/016

Platform A1 - Booth area
Previous comments are still valid, see following slides

Platform A1 - Booth area
Important: the 12 columns of the Spray Booth have been modified after change of the Scrubber technology by Renault-VAZ
5,500mm
(Internal dimension to be respected)
(wrong)
Axes 5-6/013-021

You forget the metal sheet and Omega Beam
Axes 5-6/014-015

As you will see from our Booth layout & sections, the omega’s purpose is to place the conveyor roller-bed;
Please check correct dimensions and elevation of the Omega steel profile in section H on drawing E540350033_D10_A
Full metal sheet plate (t=5mm)
Side full metal sheet plate (non structural) only for gaps flashing (t=2÷3mm)
Axes 5-6/014-015

In Base coat and Clear coat zones we have lowered beams because we’ll need to locate the Drypan scrubber (basically a big duct with filters) and the conveyor Roller-bed.
Please check our drawings (Booth layouts & sections, Drypan scrubber) for beams elevation;
Basically in these zones the TOP of the cross beams shall be at -505mm from level 4,65m = 4,145m
The bottom of this «tank» will have to be covered by full metal sheet plate (t=5mm)
The tank floor will have to foresee two holes 950x950mm (one per side) for Extraction ducts, see layouts for location
Axes 5-6/014-015
Axes 5-6/015-016

In this zone the stair that goes on 9,80m level is not alligned to ours
OK to extend platform to these columns
Platform A1 – Oven area
Axes 7/013-014

Zone: before/after the Heat wall
Please extend platform and handrail until the end of the booth (circa 500mm)
Please extend platform (circa 600mm)
Axes 5/012

Platform A1 – Oven area
Be sure to respect Oven perimeter when modeling walkable modules around it
Oven exit (circa 730mm gap)
Oven entry (circa 1,65m gap)
Axes 8/012

Platform A1 – Oven area
Oven center axis is positioned 3m west of axis 8
145mm
Fill this gap
Axes 7-8/013
Update (08/06): the Oven load is only transferred to the two longitudinal beams on each side, there’s no need to put more beams in the middle;
Also, the beams have to be no more than 145mm.

Platform D
No walkable modules under this Heater unit.
Supported by side longitudinal steel profiles
No walkable modules under this Heater unit.
Supported by side longitudinal steel profiles
Keep in mind that we have ducts penetrating platforms under the two Heater groups, these ducts will have insulation (150mm all around).
I will submit information about these duct location in order to avoid clash with supporting beams
Axes 7-8/012-019

Platform A2 – Demasking & IRC area (axes 8-10/013-015):
The area to be covered with walkable modules shall be the one circled in Yellow, basically under the two open Booths and under Electrical cabinets, as shown on General Layout uploaded in drive on 04 April (rev E – in progress)
Update:
Comment still valid

Platform A2 – Elevators area (axes 10-12/013-014):
Update:
Still not correct, use General layout to see handrails and platform configuration!

Platform A2: remember to provide holes with kick-plates around existing columns and bracing (typical) Axes 11-12/014-018
Update:
Comment still valid.
Not priority at the moment but keep it in mind for KM design